氢化物发生石墨炉原子吸收光谱法直接测定高温镍基合金中的硒

在６ｍｏｌ／Ｌ盐酸介质和０．１％ＫＢＨ４条件下，不但能有效地发生硒的氢化物，而且５ｍｇ／ｍｌＮｉ和３ｍｇ／ｍｌＦｅ都不干扰硒的测定。利用涂钯石墨；管作为氢化物的原子化器，直接测定了高温镍基合金中的硒，特征质量为４０ｐｇ，相对标准偏差在６．１％以内，回收率在９７％－１１０％之间。     

纳米多孔双金属氧化物在镍钛合金纤维上的原位生长及其对多环芳烃的选择性固相微萃取

采用阳极氧化法在镍钛合金(NiTi)纤维上原位生长了双金属氧化物纳米孔(NiTiONPs)涂层,通过扫描电镜(SEM)和能谱(EDS)考察了电解质组成和电压对形貌的影响。将NiTiONPs涂层的NiTi纤维与高效液相色谱-紫外检测器联用,研究了4种典型芳香分析物的萃取性能。结果表明,富含TiO2的NiTiONPs涂层对多环芳烃(PAHs)具有良好的萃取效率,尤其对苯并[a]芘的萃取选择性优于市售聚二甲基硅氧烷纤维和聚丙烯酸酯纤维。在优化条件下,PAHs的线性范围为0.05~200μg/L,相关系数均大于0.999,检出限为0.012~0.134μg/L。对单支纤维日内和日间分析的相对标准偏差(RSDs)分别为4.0%~5.5%和6.0%~6.8%,使用分批组装的5支纤维分析的RSDs为6.4%~7.6%。实际水样分析的加标回收率为84.5%~111.5%。所制备NiTi纤维至少可重复使用250次以上,重现性好。     

压力、温度和晶粒尺寸对Fe-N合金的合成及结构的影响

在 1× 1 0 - 3 Pa～ 4 GPa的压力和 5 80～ 930 K温度范围内 ,利用高压技术并结合机械球磨 ,研究了压力、温度和晶粒尺寸对α-Fe与非晶 BN的固态反应的影响 .发现高压和晶粒细化可以极大地促进α-Fe和非晶 BN的固态反应过程 ,α-Fe与非晶 BN发生固态反应的临界晶粒尺寸约 8nm.压力和温度对反应产物及其晶体结构有明显影响 .2 GPa和 80 0 K时 ,反应产物为具有正交结构的 Fe-N新相 ;在 3～ 4 GPa和 690～80 0 K时 ,可形成单一ε-Fex N合金相 ;而在 4 GPa和 930 K以上 ,反应产物由 Fe-N合金相转变为 Fe3B相     

Liquid-Phase Hydrogenation of Chloronitrobenzene Over Pt-Sn-B Amorphous Catalyst Supported by Carbon Nanotubes

The Pt-Sn-B/carbon nanotubes (CNTs) catalyst was prepared by impregnation-chemical reduction method. Its catalytic performance was evaluated by liquid-phase hydrogenation of chloronitrobenzene (CNB). The results showed that the catalyst had higher catalytic performance than common hydrogenation catalysts. The conversion of CNB could reach 99.9%, and the dechlorination of chloroaniline (CAN) was less than 1.9% when catalyzed by Pt-Sn-B/CNTs and more than 8.0% when catalyzed by common hydrogenation catalysts. X-ray diffraction and selected area electron diffraction analysis showed that Pt-Sn-B/CNTs had an amorphous alloy structure that can improve catalytic performance. Transmission electron micrograph image showed that the catalyst particles were highly distributed on the surface of CNTs. The hydrodechlorination of CNB was mainly affected by the unique structure of CNTs and the nature of the amorphous metals on the surface of CNTs. The relationship between the interaction of CNTs and amorphous metals and the catalytic performance of the catalyst is also discussed. Translated from the Chinese Journal of Catalysis, 2005, 26(3) (in Chinese)     

植入用Co—Cr—Mo合金与Ti—6Al—4V合金的电偶腐蚀研究

组件式设计常被用地人工髋关节，钴络钼合金（Ｃｏ－Ｃｒ－Ｍｏ）与钛合金（Ｔｉ－６Ａｌ－４Ｖ）的压配最常用，本文应用电化学方法研究了静态条件下两种合金的电偶腐蚀行为，浸泡实验表明，钴络钼合金为阳极，但电偶电流与其维钝电流相近，并无明显加速度腐蚀效应，钛合金为阴极，受到保护，失重及金相观察结果显示，在４５天的浸泡实验周期内，未发现腐蚀痕迹，混合电位理论和电位处于两种合金的钝化电位区，电偶电流为合金的维钝     

Pt/Au双金属纳米粒子的制备及表征

Poly (N-vinyl-2-pyrrolidone)-protected Pt/Au bimetallic nanoparticles were obtained by reducing the mixture of HAuCl4 and H2PtCl6 with sodium borohydride. UV-vis spectra, transmission electronic microscopy and X-my diffraction reveal that the prepared bimetallic nanoparticles are of alloy structure.     

高频燃烧红外吸收光谱法测定钨钛合金中碳含量

建立高频燃烧红外吸收光谱法测定钨钛合金中碳含量的分析方法。在1980 W分析功率下,称取0.3 g样品,以2.0 g钨锡及0.5 g纯铁混合助熔,用高频红外分析仪测定碳。碳的含量在0.013%~0.050%范围内与红外吸收峰面积线性相关,相关系数为0.9993。碳的测定下限为3.6μg/g,方法检出限为1.08μg/g。该法测定结果的相对标准偏差为2.97%~4.11%(n=8),碳的加标回收率为96.2%~103.1%。该方法能够满足合金中碳含量的分析要求。     

钇对Nd-Fe-Al-Ni非晶合金热稳定性与晶化行为的影响

采用差示扫描量热法（DSC）、X射线衍射（XRD）和透射电镜（TEM）研究了Y对Nd-Fe-Al-Ni非晶合金热稳定性和晶化行为的影响。结果表明,淬火态的Nd60Fe20Al10Ni10-xYx（x=0,2）合金基本为非晶组织同时还含有少量的淬态相,Y的加入抑制了淬态相的析出。加入Y后,非晶合金的晶化开始温度和晶化峰值温度都向高温方向移动,证明其热稳定性提高。Y的加入改变了合金的晶化方式和最终晶化产物,使非晶基体中析出的晶化相更加弥散圆整细小。并且Y具有在化学上钝化氧杂质的作用,从而抑制了氧的有害作用。利用Kissinger方程获得了Nd60Fe20Al10Ni8Y2非晶合金的晶化开始和晶化峰值激活能分别为1.21和1.16 eV。     

载体γ-Al2O3和钐对非晶态NiB合金热稳定性的影响

用化学还原法制备了NiB、NiB/Al2O3和NiBSm/Al2O3三种催化剂，它们都呈非晶结构.用等离子耦合发射光谱仪(ICP)对催化剂组分进行了分析，采用差示扫描量热法（DSC）对三种催化剂进行了热稳定性分析.结果表明，载体的引入使非晶态NiB合金的体相组成中B的含量降低.将非晶态NiB合金负载到γ-Al2O3上,可以明显改善非晶态合金的热稳定性，少量Sm可以进一步提高晶化温度.晶化激活能数据亦表明了载体和Sm对非晶结构具有良好的稳定作用.载体和Sm可能通过不同的作用提高了非晶态合金的热稳定性.     

Chemical environment of copper at the surface of a CuAl2 model alloy: XPS,MEIS and TEM analyses

Air‐formed oxide on a CuAl₂ model alloy is shown to be free of copper species, with copper enriching in the alloy. With thickening of the oxide by anodizing, copper enriches further to a critical concentration at which its oxidation proceeds with incorporation of Cu(II) species into the film. Such species migrate more rapidly through the film than aluminium species. Incorporation of copper species is associated with generation of oxygen gas within the film and subsequent film rupture is due to release of the gas. Reduction of Cu(II) to Cu(I) species during XPS analysis is characterized and the accelerating role of charge neutralizing is highlighted. Copyright © 2004 John Wiley & Sons, Ltd.